跳至主要内容

BTMA--Analysis and research on the crushing mode of the crusher



Although the crusher is a practical machine, thinking about its crushing method is still very valuable. Based on years of working experience, the author summarizes as follows:

1. Crushing: The ore is placed between two crushing surfaces, and after pressure is applied, the ore is crushed due to the compressive stress reaching the limit of its compressive strength.

2. Splitting ballast: When squeezing the ore with a flat surface and a working surface with a sharp shuttle, the ore will split along the direction of the pressure line of action. The cause of splitting is due to the tensile stress on the splitting plane reaching or exceeding the tensile strength limit of the ore. The tensile strength limit of ore is much smaller than the compressive strength limit.

3. Fracture: The ore is damaged by bending. The crushed ore is a beam with two or more fulcrums bearing concentrated loads. When the bending stress in the ore reaches the bending strength limit of the ore, the ore is broken.

4. Grinding: After the pressure and shearing force between the ore and the moving surface, the shear stress reaches the limit of the shear strength of the ore, and the rock is crushed. The ground effect is low and the energy consumption is high.

5. Impact crushing: The ore is crushed by the impact force of the high-speed rotating machine. Its crushing force is instantaneous, and its crushing efficiency is higher than that of humans, and it can significantly reduce consumption.



标签：

评论

发表评论

此博客中的热门博文

BTMA--Can the crusher handle wet materials

The crusher converts the fruit tree pruning waste branches into biomass fuel. This allows for recycling and protection of the environment. Many people ask if this equipment can handle wet materials. The crusher's performance is affected by the moisture content. Different crushers have different requirements regarding the moisture content. A higher moisture content can hinder the process of materials. Below 6% moisture level will have a good effect on the processing. This has a huge impact on crusher work and can also have a significant impact on equipment output and performance. Normal circumstances will result in the wood being fibrous when it is wet and hit with the hammer. If there are fibers, this will impact the performance of the hammer when processing. This crusher is effective. This will result in a lower efficiency. The output of the work will therefore be lower. The fiber in the middle of dry wood will be less than that of dry wood. Therefore, if the hammer or the blad...
发表评论
阅读全文

BTMA--Choosing a counterattack crusher manufacturer

The impact crusher is a machine that crushes the material by squeezing the material between the rotor and the hammer. It has a large feed inlet and conveys materials through a high-speed rotating rotor. When the plate hammer rotates, it will hit the materials in the crushing cavity and throw them upward into the impact plate. As a result, the material is crushed and then thrown out of the crushing chamber. The final particle size can be adjusted by adjusting the distance between the rotor and the impact frame. To determine which impact crusher is best for a given application, consider the following: material to be crushed, electric drive, pre-screening before the crusher, overload system, pan feeder under the crusher, and service And operator friendly. Finally, choose an impact crusher with the correct size and specifications. When purchasing an impact crusher, please consider the flow of materials through the machine. It is very important to choose the right size impact crusher manu...
3 条评论
阅读全文

BTMA--How does the jaw crusher work?

Jaw crusher is a commonly used industrial machine for crushing rocks and ore. Its main purpose is primary crushing. It has a wide range of applications, including mining, construction materials, metallurgy, electric power, and transportation. One of the characteristics of the jaw crusher is that it is relatively simple to operate and extremely versatile. The most important details about the jaw crusher are listed below: 1. How does the jaw crusher work? The main feature of the jaw crusher is the opening and the discharge port. The size of the opening determines how much material it can handle. For primary and secondary types, the gap is usually 1/3 to 1/8 of the feed size. The size of the jaw crusher depends on how big rocks it can handle and how much TPH it can produce. To determine a suitable jaw crusher, please consider its maximum stone and TPH tonnage rate. The opening of the jaw crusher is described in terms of its CSS or closed side setting. OSS is the distance between the o...
2 条评论
阅读全文